Kitchen Cabinets Installation Project – Key Points to Remember

Kitchen cabinets are not just utility fixtures. They add to the aesthetic sense and feel of the kitchen. Master interior designers have their signature layout of both wall and base cabinets that are often copied by homeowners and contractors alike.

If you have some woodworking experience from high school or some flop job joint, you may not have to spend big bucks to hire a kitchen cabinet contractor. The work is simple and straightforward if you can take proper measurements, saw sheets into corresponding pieces, and hammer nails into their place.

In this post, we are going to share some essentials that will help you in your next kitchen cabinet installation process.

Removal of Old Cabinets

Old cabinets just come off easily. They are soldered to the wall using screws and nails and it takes both strength and patience to take them out. Before straining your arms in pulling out the cabinets, locate each and every screw to ensure you are just removing the cabinets and not the wall. After removing the cabinets, remove excessive caulk from the edges by using a knife.

Ensuring Efficiency

If you are doing a grand-scale kitchen cabinet installation operation for the first time, it could be overwhelming for you. It is best to deal with every phase step by step. This will prevent any frustration and screw-ups. On a more practical note, start from the top and then move to the bottom gradually. Installing from corners allows you to work freely without getting anything in your way.

Removal of Drawers & Doors

Home Improvement Contractors of Arlington MA or any other place are aware that cabinets often come with pre-installed doors and drawers. Leaving them as they are can save you time. But it will make it harder for you to install the cabinets in the wall because they will be heavier and cumbersome to handle.

Stripping the cabinets from their doors and drawers will give you the freedom to screw them with the wall without straining. Make sure you mark the constituents before removing them so that they can be installed back to their original places.

Benchmark Line

Before commencing your work of cabinet installation, draw a benchmark line. It can at any height of the room. The main purpose of this line is to make sure the cabinets are installed at a perfectly leveled height. This line will go throughout the perimeter of the kitchen and you can sketch a base point for any fixture by measuring from or to the base and wall.

Support for Cabinet Weight

Installing kitchen cabinets in its place is usually a two-man job so you do not have to worry about handling it all alone. Still, to make the process easier, place a cleat along the wall that goes through the length of the cabinets in the bottom. This is an effective way to balance the cabinets. There are chances of the cabinet slipping forward, but you will have more grip and easy reach to install it properly.

Usage of Nails During Kitchen Cabinet Installation

Nails are often used by professionals instead of screws during a kitchen cabinet installation because of their easy handling and relatively firm grip. They are normally used behind the cabinets to save the façade. When you are using nails, make sure to locate and nail the studs for lasting installation.

You can also make a small hole in the wall which will give you a path where to drive the nails in the cabinets.

Kitchen Cabinet Installation Plan

Starting off is easy as long as you do not have to go far. Installing kitchen cabinets is sophisticated work. You should plan your movements beforehand to avoid any confusion or extra costs.

Layout a plan to see where all the appliances and fixtures go. These include refrigerator, oven, cooking range, power outlets, etc. Once you have a clear picture of the kitchen, it becomes very easy to install the cabinets without kitting a speed bump.

If the whole process seems overwhelming to you, you can find cabinet installation services in Golden Valley MN.

Microwave Outlet

Saving space for the microwave is essential. First off, make sure the contractor has installed a power delivery point for the oven in the intended spot. This will allow you to operate the microwave without any hiccup.

Cabinet Fillers

It is perfectly normal to have little gaps between cabinets and kitchen walls when you are done with installation. Every packaging has scribe or filler pieces to fill these gaps. Walls are not straight to a point which is the main reason behind these gaps.

The main purpose of a scribe filling is to keep the moving parts of a cabinet away from the wall to prevent any possible damage.

Do not rush with the project. Take extra caution throughout the process. When in doubt, move back a step and get a new perspective on the build. By following these steps, you can finish your cabinet installation project successfully.

Hannah Oscar is a professional writer and digital marketer. She works for a free online business directory called the highfive listings.





Is Gmail Account Not Responding Due To Is Gmail Down Problems?

In the blog below, we have discussed some effective remedies to fix Google not working problems. However, we have also shared some essential information...

Expressions and Crafts Recommendation to Urge Started

Expressions and Crafts recommendation to urge started. Expressions and Crafts specialties come to have for quite your time been strategies for act originality and...

Things You Should Be Careful about when Buying Bitcoin

2022 has so far not been a remarkable year for cryptocurrency as many digital currencies have lost value, particularly Bitcoin (BTC). But does this mean...

Master Suggestion on Acquiring the Arts and Crafts

Master suggestion on acquiring the Arts And Crafts. Have you at any point cherished a lump of plan that someone had made and confused...

DAO Communication What Makes a Tool Great

Introduction You might be wondering what makes a great communication tool for a DAO. Is it something that's easy to use? Is it secure? Is it...